![]() The woman lost an acrylic nail and required stitches, according to Animal Services. When the bite occurred, she was in the bathroom where Scoop usually stays when Remson is not home, records show. – A bulldog died while in Orange County Animal Services custody and now the owner wants to know what happened.Īccording to a report from Orange County Animal Services, a 20-year-old woman said she was at Darryl Remson's unit at 55 West Apartments in Orlando on Sunday when Scoop, a 3-year-old black and white American bulldog, bit her left index finger as she reached down to pet him. I have sent you a private message, for more details that cannot be shared in a public post.Ĭan you please check your inbox on the forums page for the private message.ORANGE COUNTY, Fla. However, to provide accurate details, I need a few more details: If the Print Quality Diagnostic report does not show track marks or smears, If the Print Quality Diagnostic report shows track marks or smears, continue to the next step to clean the area around the ink nozzles. If these steps resolved the issue, you can stop troubleshooting. ![]() Print another Print Quality Diagnostic report, and examine the page. Lift the scanner lid, and then place the page on the glass according to the instructions on the alignment page.Ĭlose the scanner lid, and then touch OK. The printer prints a test page, and then prompts you to scan the page. Touch Tools, and then touch the Down Arrow once. Load plain white paper in the paper tray. The printer cleans the ink cartridges again, and then prints another test page.įor the best print quality, align the ink cartridges. If the print quality is not good, touch Clean Again. If the print quality is good, touch Done. The printer cleans the printhead, and then prints a test page.Ĭheck the print quality of the test page. Touch Tools, and then touch Clean Printhead. On the printer control panel, touch the Settings icon. To avoid issues that require cleaning, always turn the printer off with the Power button. If you found defects on the Print Quality Diagnostic Report, run an automatic tool to clean the ink cartridges. If you are facing the same issue, Clean the ink cartridges Repeat these steps to clean the area surrounding the ink nozzle on the other ink cartridge. Hold the ink cartridge at a slight upward angle with the ink cartridge contacts facing the rear of the printer, and then slide the ink cartridge into the empty slot.Ĭlose the ink cartridge lid to secure the ink cartridge into place. Lightly moisten a clean, foam-rubber swab with distilled water, and then squeeze any excess water from it.Ĭlean the face and edges around the ink nozzle with the swab.įigure : Clean the area around the ink nozzleĮither let the ink cartridge sit for 10 minutes to allow the cleaned area to dry, or use a new swab to dry it. Touching these parts can result in clogs, ink failure, and bad electrical connections.įigure : Do not touch the contacts or nozzles Inspect the ink cartridge contacts for ink and debris buildup.ĭo not touch the copper-colored contacts or the ink nozzles. Do not leave an ink cartridge outside the printer for more than 30 minutes.įigure : Hold the ink cartridge by its sides ![]() Remove and clean each ink cartridge one at a time. Pull up on the ink cartridge to remove it from the slot.ĭo not remove both ink cartridges at the same time. To release the ink cartridge, lift the lid on the ink cartridge slot, and then gently push the lid back until it stops. Wait until the carriage is idle and silent before continuing. The carriage moves to the ink cartridge access area. These can damage the ink cartridge or the printer. Clean the area around the ink nozzles if you see track marks or smears on the printouts.įigure : Example of text with track marksĭry foam-rubber swabs, lint-free cloth, or any soft material that does not come apart or leave fibers (coffee filters work well)ĭistilled, filtered, or bottled water (tap water might contain contaminants that can damage the ink cartridges)ĭo not use platen cleaners or alcohol to clean the area. Let's clean the area around the ink nozzlesĭo not perform these steps unless the test page or printout specifically shows smeared text or track marks. I understand that you are getting print quality issue while printing.Īre you facing the same issue while making a copy?Īre you using instant ink or regular cartridge? This is a great place to get support, find answers to your technical queries. Business PCs, Workstations and Point of Sale Systems.Printer Wireless, Networking & Internet.DesignJet, Large Format Printers & Digital Press.Printing Errors or Lights & Stuck Print Jobs.Notebook Hardware and Upgrade Questions.
0 Comments
Leave a Reply. |